Parts for uds?

All about smokers hot and cold
Post Reply
blucmal
Posts: 8
Joined: Sun Aug 11, 2019 11:09 am

Parts for uds?

Post by blucmal » Tue Oct 01, 2019 4:29 pm

Looking for pipe to do my inlet and outlet on my uds. Cant find any black pipe in my area,Gympie Qld. Or do people use galvanised? Not sure I like that idea. Also for mesh for a basket.


Unzippy
Posts: 44
Joined: Sun Jan 28, 2018 1:04 am
Location: Melbourne

Re: Parts for uds?

Post by Unzippy » Wed Oct 02, 2019 4:32 pm

I used gas pipe and fittings from Bunnings plumbing dept.

blucmal
Posts: 8
Joined: Sun Aug 11, 2019 11:09 am

Re: Parts for uds?

Post by blucmal » Wed Oct 02, 2019 10:43 pm

galvanised stuff?

Unzippy
Posts: 44
Joined: Sun Jan 28, 2018 1:04 am
Location: Melbourne

Re: Parts for uds?

Post by Unzippy » Fri Oct 04, 2019 3:51 pm

blucmal wrote:
Wed Oct 02, 2019 10:43 pm
galvanised stuff?
Yup, for the inlet stuff.

blucmal
Posts: 8
Joined: Sun Aug 11, 2019 11:09 am

Re: Parts for uds?

Post by blucmal » Sun Oct 06, 2019 4:11 pm

ok thanks :D

blucmal
Posts: 8
Joined: Sun Aug 11, 2019 11:09 am

Re: Parts for uds?

Post by blucmal » Sat Oct 19, 2019 5:08 pm

Drum is built wondering do i need an ash catcher on chimney? I have a large fire hazzard running through yard. How many embers do these things spit out?
Resized_20191017_135411.jpeg
Resized_20191017_135411.jpeg (213.64 KiB) Viewed 256 times

Unzippy
Posts: 44
Joined: Sun Jan 28, 2018 1:04 am
Location: Melbourne

Re: Parts for uds?

Post by Unzippy » Mon Oct 21, 2019 10:37 am

Looking good!

Minimal to no sparks.
They would have to make it all the way up to the top of the barrel, find the bottom of the chimney and then up and out. Also they are not running grilling temps, just ticking over on low and slow.
Maybe a little hat would be sufficient?

blucmal
Posts: 8
Joined: Sun Aug 11, 2019 11:09 am

Re: Parts for uds?

Post by blucmal » Mon Nov 11, 2019 5:27 pm

I ended up putting stainless mesh over chimney then a hat to stop rain..

I have used it fair bit and your right no sparks and very low heat I can hold end of chimney. Works awesome and cooks delicious food. I have been using heat beads brand lump charcoal. I dont use extra wood. I reakon it has enough flavour. Nice thin blue smoke :D

Unzippy
Posts: 44
Joined: Sun Jan 28, 2018 1:04 am
Location: Melbourne

Re: Parts for uds?

Post by Unzippy » Mon Nov 18, 2019 7:21 pm

blucmal wrote:
Mon Nov 11, 2019 5:27 pm
I ended up putting stainless mesh over chimney then a hat to stop rain..

I have used it fair bit and your right no sparks and very low heat I can hold end of chimney. Works awesome and cooks delicious food. I have been using heat beads brand lump charcoal. I dont use extra wood. I reakon it has enough flavour. Nice thin blue smoke :D
Fantastic 8)


Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests